HomePLC Programming
Motion Control
Control Panels

Contact Us

Control System Engineers, PLC programmers & Motion Control Experts

Allen Bradley           Control Techniques            Bosch Rexroth            Omron              Siemens                  Mitsubishi             Automation Direct             Koyo            Allen Bradley           Control Techniques            Bosch Rexroth            Omron              Siemens                  Mitsubishi             Automation Direct             Koyo       



We are able to diagnose and repair your machinery.

Utilising years of experience in control systems and automation engineering as well as our wide range of software tools and test equipment we can get you up and running quickly.

If you need help with any control system, PLC, AC drives, DC drives, Servo, HMI, SCADA, mechnical, pneumatic or hydraulic problems we can help. Call us for free and friendly advice.

We are able to supply PLC's, Drives, HMI's from many manufacturers at discounted prices as well as obsolete equipment.

We can also help with Preventative / Scheduled maintenance




Any Industry         Any Application         Anywhere


 Tel:  0845 838 7048

  Copyright Wolf Automation 2009     Email:Info@wolfautomation.co.uk  

                                                        PLC Programmer          Motion Control         Breakdown Services         Control Panels         Design         News         Industries          Contact











Maybe you need a PLC Programmer to fault find your plant, maybe you need a PLC programmer to improve a machines performance. Whatever the reason you need a PLC programmer call us on 07966 636586. Take a look at the other services our engineers provide and contact us for a free quotation with no obgligation.

If you are just interested in PLC's or want to know what it is, here is what you are looking for:

What is a programmable Logic Controller (PLC)

A Programmable Logic Controller, PLC, or Programmable Controller is a small computer used for automation of industrial processes, such as control of machinery on factory assembly lines. Unlike general-purpose computers, the PLC is designed for extended temperature ranges, dirty or dusty conditions, immunity to electrical noise, and resistance to vibration and impact. Programs to control machine operation are stored in battery-backed or read-only memory. A PLC is an
example of a real time system since output results must be produced in response to input conditions within a strictly bounded time.

The main difference from other computers are the special input/output arrangements. These connect the PLC to sensors and actuators. PLCs read limit switches, temperature indicators and the positions of complex positioning systems. Some even use machine vision. On the actuator side, PLCs drive any kind of electric motor, pneumatic or hydraulic cylinders or diaphragms, magnetic relays or solenoids. The input/output arrangements may be built into a simple PLC, or the PLC may have external I/O modules attached to a proprietary computer network that plugs into the PLC.

PLCs were invented as replacements for automated systems that would use hundreds or thousands of relays and cam timers. Often, a single PLC can be programmed to replace thousands of relays. Programmable controllers were initially adopted by the automotive manufacturing industry, where software revision replaced the re-wiring of hard-wired control panels when production models changed.

The earliest PLCs expressed all decision making logic in simple ladder logic which appeared similar to electrical schematic diagrams. The electricians were quite able to trace out circuit problems with schematic diagrams using ladder logic. This program notation was chosen to reduce training demands for the existing technicians.

The functionality of the PLC has evolved over the years to include sequential relay control, motion control, process control, distributed control systems and networking. The data handling, storage, processing power and communication capabilities of some modern PLCs are approximately equivalent to desktop computers. PLC-like programming combined with remote I/O hardware, allow a general-purpose desktop computer to overlap some PLCs in certain applications.

Under the IEC 61131-3 standard, PLCs can be programmed using structured programming languages. A graphical programming notation called Sequential Function Charts is available on certain programmable controllers.

PLC Manufacturers

Allen Bradley  SLC 505, SLC 5/01 SLC 5/03 SLC 5/05, Mitsubishi F1, F2, FX, FX0, FX1, FX2. Omron C200h, CQM. Modicon Telemanique Twido,, Siemens S5, S7. Direct Logic , Koyo DL06. Control Techniques Unidrive, SP

PLC compared with other control systems

PLCs are well-adapted to a certain range of automation tasks. These are typically industrial processes in manufacturing where the cost of developing and maintaining the automation system is high relative to the total cost of the automation, and where changes to the system would be expected during its operational life. PLCs contain input and output devices compatible with industrial pilot devices and controls; little electrical design is required, and the design problem centers on expressing the desired sequence of operations in ladder logic (or function chart) notation. PLC applications are typically highly customized systems so the cost of a packaged PLC is low compared to the cost of a specific custom-built controller design. On the other hand, in the case of mass-produced goods, customized control systems are economic due to the lower cost of the components, which can be optimally chosen instead of a "generic" solution, and where the non-recurring engineering charges are spread over thousands of sales.

Some modern PLCs with full capabilities are available for a few hundred USD. This allows them to be economically applied on very small control problems.

For high volume or very simple fixed automation tasks, different techniques are used. For example, a consumer dishwasher would be controlled by an electromechanical cam timer costing only a few dollars in production quantities.

A microcontroller-based design would be appropriate where hundreds or thousands of units will be produced and so the development cost (design of power supplies and input/output hardware) can be spread over many sales, and where the end-user would not need to alter the control. Automotive applications are an example; millions of units are built each year, and very few end-users alter the programming of these controllers. (However, some specialty vehicles such as transit busses economically use PLCs instead of custom-designed controls, because the volumes are low and the development cost would be uneconomic.)

Very complex process control, such as used in the chemical industry, may require algorithms and performance beyond the capability of even high-performance PLCs. Very high speed controls may also require customised solutions; for example, aircraft flight controls.

PLCs may include logic for single-variable feedback analog control loop, a "proportional, integral, derivative" or "PID controller." A PID loop could be used to control the temperature of a manufacturing process, for example. Historically PLCs were usually configured with only a few analog control loops; where processes required hundreds or thousands of loops, a distributed control system (DCS) would instead be used. However, as PLCs have become more powerful, the boundary between DCS and PLC applications has become less clear-cut..


Digital and analog signals

Digital or discrete signals behave as switches, yielding simply an On or Off signal (1 or 0, True or False, respectively). Pushbuttons, limit switches, and photo-eyes are examples of devices providing a discrete signal. Discrete signals are Sent using either voltage or current, where a specific range is designated as On and another as Off. A PLC might use 24 V DC I/O, with values above 22 V DC representing On and values below 2VDC representing Off. Initially, PLCs had only discrete I/O.

Analog signals are like volume controls, with a range of values between zero and full-scale. These are typically interpreted as integer values (counts) by the PLC, with various ranges of accuracy depending on the device and the number of bits available to store the data. Pressure, temperature, flow, and weight are often represented by analog signals. Analog signals can use voltage or current with a magnitude proportional to the value of the process signal. For example, an analog 4-20 mA or 0 - 10 V input would be converted into an integer value of 0 - 32767.

Current inputs are less sensitive to electrical noise (i.e. from welders or electric motor starts) than voltage inputs.



As an example, say the facility needs to store water in a tank. The water is drawn from the tank by another system, as needed and our example system must manage the water level in the tank.

Using only digital signals, the PLC has two digital inputs from float switches (tank empty and tank full). The PLC uses a digital output to open and close the inlet valve into the tank.

If both float switches are off (down) or only the 'tank empty' switch is on, the PLC will open the valve to let more water in. If only the 'tank full' switch is on, the valve turns off. Both switches being on would signal that something is wrong with one of the switches, as the tank cannot be both full and empty at the same time. Two float switches are used to prevent a 'flutter' condition where any water usage activates the pump for a very short time causing the system to wear out faster.

An analog system might use a load cell (scale) that weighs the tank, and an adjustable (throttling) valve. The PLC could use a PID feedback loop to control the valve opening. The load cell is connected to an analog input and the valve is connected to an analog output. This system fills the tank faster when there is less water in the tank. If the water level drops rapidly, the valve can be opened wide. If water is only dripping out of the tank, the valve adjusts to slowly drip water back into the tank.

In this system, to avoid 'flutter' adjustments that can wear out the valve, many PLCs have a "deadband". A technician adjusts this deadband so the valve moves only for a significant change in rate. This will in turn minimize the motion of the valve, and reduce its wear.

A real system might combine both approaches, using float switches and simple valves to prevent spills, and a rate sensor and rate valve to optimize refill rates. Backup and maintenance methods can make a real system very complicated.


PLCs package will work on I/O capabilities: Modular, Rack, P2P

Modular PLCs have a limited number of connections built in for inputs and outputs. Typically, expansions are available if the base model does not have enough I/O.

Rack-style PLCs have processor modules with separate [optional] I/O modules, which may occupy many racks. These often have thousands of discrete and analog inputs and outputs. Often a special high speed serial I/O link is used so that racks can be remotely mounted from the processor, reducing the wiring costs for large plants. Some of today's PLCs can communicate over a wide range of media including RS-485, Coaxial, and even Ethernet for I/O control at network speeds up to 100Mbps.

PLCs used in larger I/O systems may have peer-to-peer (P2P) communication between processors. This allows separate parts of a complex process to have individual control while allowing the subsystems to co-ordinate over the communication link. These communication links are also often used for HMI devices such as keypads or PC-type workstations.

A rule-of thumb is that the average number of inputs installed is three times that of outputs for both analog and digital. The 'extra' inputs arise from the need to have redundant methods to monitor an instrument to appropriately control another, and from the need to use both manual command inputs to the system and feedback from the controlled system itself.



Early PLCs, up to the mid-1980s, were programmed using proprietary programming panels or special-purpose programming terminals, which often had dedicated function keys representing the various logical elements of PLC programs. Programs were stored on cassette tape cartridges. Facilities for printing and documentation were very minimal due to lack of memory capacity. More recently, PLC programs are typically written in a special application on a personal computer, then downloaded by a direct-connection cable or over a network to the PLC. The very oldest PLCs used non-volatile magnetic core memory but now the program is stored in the PLC either in battery-backed-up RAM or some other non-volatile flash memory.

Early PLCs were designed to be used by electricians who would learn PLC programming on the job. These PLCs were programmed in "ladder logic", which strongly resembles a schematic diagram of relay logic. Modern PLCs can be programmed in a variety of ways, from ladder logic to more traditional programming languages such as BASIC and C. Another method is State Logic, a Very High Level Programming Language designed to program PLCs based on State Transition Diagrams.

Recently, the International standard IEC 61131-3 has become popular. IEC 61131-3 currently defines five programming languages for programmable control systems: FBD (Function block diagram), LD (Ladder diagram), ST (Structured text, similar to the Pascal programming language), IL (Instruction list, similar to assembly language) and SFC (Sequential function chart). These techniques emphasize logical organization of operations.

While the fundamental concepts of PLC programming are common to all manufacturers, differences in I/O addressing, memory organization and instruction set mean that PLC programs are never perfectly interchangeable between different makers. Even within the same product line of a single manufacturer, different models may not be directly compatible.


User interface

PLCs may need to interact with people for the purpose of configuration, alarm reporting or everyday control. A Human-Machine Interface (HMI) is employed for this purpose.

A simple system may use buttons and lights to interact with the user. Text displays are available as well as graphical touch screens. Most modern PLCs can communicate over a network to some other system, such as a computer running a SCADA (Supervisory Control And Data Acquisition) system or web browser.



PLCs usually have built in communications ports for at least RS232, and optionally for RS485 and ethernet. Modbus is the lowest common denominator communications protocol. Others are various fieldbuses such as Profibus.



The PLC was invented in response to the needs of the American automotive industry. Before the PLC, control, sequencing, and safety interlock logic for manufacturing automobiles was accomplished using relays, timers and dedicated closed-loop controllers. The process for updating such facilities for the yearly model change-over was very time consuming and expensive, as the relay systems needed to be rewired by skilled electricians. In 1968 GM Hydramatic (the automatic transmission division of General Motors) issued a request for proposal for an electronic replacement for hard-wired relay systems.

The winning proposal came from Bedford Associates of Boston, Massachusetts. The first PLC, designated the 084 because it was Bedford Associates eighty-fourth project, was the result. Bedford Associates started a new company dedicated to developing, manufacturing, selling, and servicing this new product: Modicon, which stood for MOdular DIgital CONtroller. One of the people who worked on that project was Dick Morley, who is considered to be the "father" of the PLC. The Modicon brand was sold in 1977 to Gould Electronics, and later acquired by German Company AEG and then by Schneider Electric, the current owner.

One of the very first 084 models built is now on display at Modicon's headquarters in North Andover, Massachusetts. It was presented to Modicon by GM, when the unit was retired after nearly twenty years of uninterrupted service.

The automotive industry is still one of the largest users of PLCs, and Modicon still numbers some of its controller models such that they end with eighty-four. PLCs are used in many different industries and machines such as packaging and semiconductor machines. Well known PLC brands are ABB Ltd., Koyo, Honeywell, Siemens, Modicon, Omron, Allen-Bradley, General Electric, Tesco Controls, Panasonic (Matsushita), and Mitsubishi.

We are

  • Freelance PLC Programmers

  • Allen Bradley PLC programmers

  • Mitsubishi PLC programmers

  • Siemens S5 PLC Programmers

  • Siemens S7 PLC Programmers

  • Omron PLC programmers

  • Koyo PLC Programmers

  • Telemecanique PLC Programmers

  • Modicon PLC Programmers

  • Twido PLC programmers

  • PanelView Programmers

  • Redlion Programmers

  • Panel Builder Programmers

  • Visual Basic Programmers

  • Fix Programmers

  • Wonderware InTouch Programmers

  • Opto Programmers

  • Control Techniques Programmers

  • Motion Control Programmers

  • Indramat Programmers

  • Freelance PLC programmer

We Service and Repair

  • PLC's

  • AC Drives

  • DC Drives

  • Servo Drives

  • Servo Motors

  • Rolling Mills

  • Packing Machines

  • Rubber Machinery

  • Food Production Plant

  • Industrial Wash Machines

  • Pipe and Tube Straigteners

  • Tyre and Tube Machinery

  • Hydraulic Presses

  • Mechanical presses

  • Flying Shears

  • Rollfeeders

  • Rotary Pierce machines

  • Knurl machines

  • Ultra Steel Production Machines

  • Conveyer Equipment

We Have worked on Every Continent in Contries including:

  • USA

  • Canada

  • Russia

  • Indonesia

  • India

  • China

  • Singapore

  • Australia

  • Spain

  • Gibralta

  • Norway

  • Iceland


Allen Bradley  SLC 505, SLC 5/01 SLC 5/03 SLC 5/05, Bosch Rexroth, Indramat, Mitsubishi F1, F2, FX, FX0, FX1, FX2. Omron C200h, CQM. Modicon Telemanique Twido,, Siemens S5, S7. Direct Logic , Koyo DL06. Control Techniques Unidrive, SP


PLC    Motion Control    Control Panels    SCADA      HMI     Electrical Design

Steel Industry   Cold Roll Forming    Tyre Industry

 Free UK Business Directory

Engineering Directory - Directory listing UK engineering companies.


Automation and motion technology A&M technology AMT bubble automation control system integrator integration